CONFIGURE STATIC ROUTING ( IPV6 ) ON CISCO ROUTER

In this post i will show you how to configure static routing on Cisco routers . I have shown in previous articles how to configure static routing in ipv4 . In this lab i have configured static routing (ipv6 ) using four routers . We use static routing  when you statically configure a router to send packets for particular destinations in preconfigured directions.

static routing ipv6

ROUTERS CONFIGURATION

R1

Router>en
Router#config t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#ipv6 unicast-routing
Router(config)#int fa0/0
Router(config-if)#ipv6 add 2003::2/64
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

Router(config-if)#exit
Router(config)#int fa0/1
Router(config-if)#ipv6 add 2000::1/64
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up

Router(config-if)#exit
Router(config)#int eth0/0/0
Router(config-if)#ipv6 add 2004::1/64
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface Ethernet0/0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/0/0, changed state to up

Router(config-if)#exit
Router(config)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config)#ipv6 route 2007::/64 2003::1
Router(config)#ipv6 route 2002::/64 2003::1
Router(config)#ipv6 route 2005::/64 2000::2
Router(config)#ipv6 route 2001::/64 2000::2
Router(config)#ipv6 route 2006::/64 2000::2
Router(config)#

R2

Router>en
Router#config t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#ipv6 unicast-routing
Router(config)#int fa0/0
Router(config-if)#ipv6 add 2001::1/64
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#exit
Router(config)#int fa0/1
Router(config-if)#ipv6 add 2000::2/64
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up

Router(config-if)#exit
Router(config)#int eth0/0/0
Router(config-if)#ipv6 add 2005::1/64
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface Ethernet0/0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/0/0, changed state to up

Router(config-if)#exit
Router(config)#ipv6 route 2006::/64 2001::2
Router(config)#ipv6 route 2002::/64 2001::2
Router(config)#ipv6 route 2007::/64 2001::2
Router(config)#ipv6 route 2003::/64 2000::1
Router(config)#ipv6 route 2004::/64 2000::1
Router(config)#

R3

Router>en
Router#config t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#ipv6 unicast-routing
Router(config)#int fa0/0
Router(config-if)#ipv6 add 2003::1/64
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#exit
Router(config)#int fa0/1
Router(config-if)#ipv6 add 2002::2/64
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up

Router(config-if)#exit
Router(config)#int eth0/0/0
Router(config-if)#ipv6 add 2007::1/64
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface Ethernet0/0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/0/0, changed state to up

Router(config-if)#exit
Router(config)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to down

Router(config)#ipv6 route 2004::/64 2003::2
Router(config)#ipv6 route 2000::/64 2003::2
Router(config)#ipv6 route 2006::/64 2002::1
Router(config)#ipv6 route 2001::/64 2002::1
Router(config)#ipv6 route 2005::/64 2002::1
Router(config)#

R4

Router>en
Router#config t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#ipv6 unicast-routing
Router(config)#int fa0/1
Router(config-if)#ipv6 add 2001::2/64
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up

Router(config-if)#exit
Router(config)#int fa0/0
Router(config-if)#ipv6 add 2002::1/64
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#exit
Router(config)#int eth0/0/0
Router(config-if)#ipv6 add 2006::1/64
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface Ethernet0/0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/0/0, changed state to up

Router(config-if)#exit
Router(config)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up

Router(config)#ipv6 route 2005::/64 2001::1
Router(config)#ipv6 route 2000::/64 2001::1
Router(config)#ipv6 route 2004::/64 2001::1
Router(config)#ipv6 route 2003::/64 2002::2
Router(config)#ipv6 route 2007::/64 2002::2
Router(config)#

Now assign ip to each end devices (laptop or pc) .

Go to   DESKTOP > IP CONFIGURATION 

ipv6 configuration

ipv6 configuration

ipv6 configuration

ipv6 configuration

NOW TRY TO PING . IF its pinging means static routing routing has been configured . If its not then you might have made few mistakes .

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s